Pallet wrapper training | Quick reference guide for HMI PANEL

Pallet wrapper Training quick Refence Guide for HMI Panel

This is not a safe operating procedure; personnel should already be familiar with the safety aspects and risks of the Atlanta pallet wrapping machine.

This guide is for the ATLANTA STRETCH Mytho S pallet wrapper with HMI equipped.  

You can download a pdf version of this guide at the bottom of the page. 

 

Starting pallet wrapper

Make sure the power has been turned on at the power point.

  1. Activate pallet wrapper by turning on the main switch.
  2. Wait until the HMI panel is ready.
  3. The pallet wrapper will be in alarm E03, HMI panel will be RED.
  4. Press the blue reset button once.
  5. The Atlanta pallet wrapper should now be ready for use, HMI panel will be GREEN.

 

If the pallet wrapper is still in alarm mode and HMI panel is still RED take note of the number above the QR code and call your team leader. or MPS (1300 396 835)

Under no circumstances

Drop the stretch wrap roll onto the carriage, this may cause damage to the carriage guides.

Loading stretch wrap

Using the correct stretch wrap, lower the stretch wrap roll onto the holder with a smooth motion, feed the stretch wrap through the carriage, there will be a guide on how to feed the stretch wrap located on the carriage.

Carriage won’t rise.

Please speak to your team leader or call MPS (1300 396 835)

E03 appears.

IF the E03 doesn’t go away following the start-up procedure, please call your tam leader 1st, then call  MPS if E03 continues.

E04 appeared.

An object is under the carriage crush zone, please remove the object. Clear the error by pressing the reset on the HMI panel.

E09 appeared.

With the OPRS and PRS carriages E09 will appear if the stretch film has broken, or the roll is empty. Re-attach film, clear error by pressing reset on the HMI panel, press the green start button to continue cycle.

E16 appears.

Check Emergency stop button that it isn’t engaged. Check the carriage door on the PRS only if it is closed properly. If error still exists pls call MPS (1300 396 835)

 

Turntable won’t stop.

If the turntable just keeps turning and won’t stop, please call MPS. (1300 396 835)             

Service

It is recommended daily that you keep the area clean of any rubbish, depending on the usage we offer 3 months, 6 months service intervals, during the service the pallet wrapper will be out of order.

 

Smart Page

  1. Lock (restricted access)
  2. Available programs to select.
  3. The active options for the activated / in use program are displayed.
  4. Self-diagnosis to check the wear status of the machine.
  5. Reset press for 3 seconds to reset the functions activated by the software, in case of alarms for emergencies, it is also necessary to intervene with the physical RESET button on the machine.
  6. Press to access the relevant function changes to functions only can occur in the cycle in progress. It does not overwrite the stored program.
  7. Displays the current program selected.

 

Home screen.

 

 

 

 

Adjusting the film tension.

  1. If you want the tension to be the same value for F13, F14, F15 and F16
  2. F13 tension for the lower wraps, adjust to desired setting.
  3. F14 tension for ascent wraps, adjust to desired setting.
  4. F15 tension for high wraps, adjust to desired setting.
  5. F16 tension for descent, adjust to desired setting.
  6. Press to save the changes and return to HOME.

Adjusting the carriage speed.

 

  1. If you want the carriage speed to be the same for ascent and descent.
  2. Ascent speed, adjust to desired speed.
  3. Descent speed, adjust to desired speed.
  4. Press to save the changes and return to HOME.

 

 

 

 

Adjusting low and top wraps

  1. Adjustment for the number of Top wraps.
  2. Adjustment for the number of lower wraps.
  3. Press to save the changes and return to HOME.

Adjusting turntable speed.

  1. Adjustment for the turntable speed.
  2. Press to save the changes and return to HOME.

 

 

 

 

 

General Questions:

  1. What is the blue reset // button used for.

A: The physical blue button is used to enable the machine and ensure that it turns on and verify that the emergency circuit is correctly closed.

  1. Can I use the Emergency Stop all the time.
  2. No, the emergency stop button should only be used for Emergencies!
  3. Can I stop the cycle at any time?
  4. Yes, press the RED stop button, then press the Green Start button to continue the cycle.
  5. When in manual mode, how do I stop the cycle correctly.
  6. When you finish using the manual cycle, press the rotate table So, the table will stop in the homing position.

 

We hope you found our guide on using the Mytho S pallet wrapper panel helpful.